Our Heat Sealers are used to seal plastic bags and film. They come in both hand operated and foot operated (to allow the operators hands to be free). They are all 240V and portable in their construction.
| Model | Sealing Width | |
| Hand Operated | TISH200 | 200mm |
| TISH300 | 300mm | |
| Foot Operated | TISF450 | 450mm |
| TISF600 | 600mm |
Our machine level pads are designed to remove machine vibration during running and to level the machine to the horizontal. This creates an environment that gives your machine accuracy, long life, reduction of operator fatigue and reduction of noise.
They are made of powder coated steel with neoprene feet which are resistant to factory processing oils and heat.
| Model | Load Capacity | Pad Diameter | Bolt Diameter |
| LP1 | 0-400kg | 104mm | 12mm |
| LP2 | 400-1000kg | 145mm | 18mm |
| LP3 | 1000-2000kg | 195mm | 18mm |
| LP4 | 2000-3000kg | 228mm | 24mm |
| LP5 | 3000-5000kg | 250mm | 30mm |
These are essential to have installed to every plastics processing machine feed hopper to remove any ferrous metal contamination that can damage screws, barrels and dies.
They come in different sizes from 5″ to 11″ to suit all types and sizes of hoppers.
| Model | L (mm) | W (mm) | H (mm) | Type |
| 5″ Round | 120 | 112 | 90 | Round type – 5 bars |
| 5″ Square | 120 | 112 | 90 | Square type – 5 bars |
| 7″ Round | 180 | 175 | 75 | Round type – 7 bars |
| 7″ Square | 180 | 175 | 75 | Square type – 7 bars |
| 8″ Round | 185 | 163 | 32 | Round type – 4 bars |
| 9″ Round | 230 | 218 | 75 | Round type – 9 bars |
| 9″ Square | 230 | 218 | 75 | Square type – 9 bars |
| 11″ Round | 265 | 265 | 75 | Round type – 11 bars |
Die Clamps are used for holding dies in processing machine platens and are available in two different types with the following sizes in our range.
| Clamp Type | Bolt Size | Length |
| Boat | 12mm | 100mm |
| 16mm | 125mm | |
| 20mm | 160mm | |
| 25mm | 200mm | |
| Slotted | 12mm | 100mm |
| 16mm | 150mm | |
| 20mm | 200mm | |
| 25mm | 250mm | |
| Toggle | 16mm | 120mm |
| 20mm | 150mm |
Onda Water Flow Meters are required to control the flow and temperature of water through your die and/or processing machine. This gives you the ultimate in die temperature control for the most accurate and fastest moulding conditions your processing machine is capable of.
They are available for all size processing machines and dies and have models from .2L/min to 30L/min and in combinations up to 12 zones per unit. Zones can be baffled and can handle both hot and cold water zones in the one water flow meter.
Construction is of glass filled nylon and the viewing tubes are unbreakable and made of clear nylon. MADE IN TAIWAN
| Model | Maximum L/min per zone | Number of zones available |
| FSM400 | 8L/min | 1-12 |
| FSML400 | 20L/min | 1-12 |
| FSML400-300 | 30L/min | 1-12 |
Reviews
There are no reviews yet.